Assessing the condition of urban tree habitats using Biodiversity Metric 3.0
Our recent blog – Valuing our urban trees I, pointed out the failings of the methodology for calculating the size of urban tree habitats as set out in Biodiversity Metric 3.0 (BNG 3.0). We would now like to show how this is compounded by the inappropriate assessment criteria used to determine the condition of Urban Tree habitats, as also set out in BNG 3.0 (see Annex 1).
We use the following example – taken from a recently approved planning application[1] which will result in the removal of 13 urban trees – to demonstrate why this is approach is inappropriate.
Figure 1 The example tree – Google Street View 2020
This street tree is a London Plane (Platanus × acerifolia) with a stem diameter (called DBH) of 118 cm. It is a non-native species planted in hard standing on Bridge St, Bristol BS1 2AN in about 1967. Using BS 5837:2012 – Trees in relation to design, demolition and construction – Recommendations (a BSI Standards Publication), it has been categorised as A,1,2 (see Annex 2). The developer’s Arboriculturalist described it as having a ‘Large, broad crown with excellent form and vigour.’
The tree’s BS 5837:2012-calculated Root Protection Area (RPA) radius[3] is 14.6 metres, so it has an RPA of 630 square metres. The tree has an average crown radius of 9.88 metres and a calculated canopy area of 306 square metres.
Using BNG 3.0 TABLE 7-2: Urban tree size by girth and their area equivalent (see Annex 1), the calculated RPA of the tree is set at Large, so its habitat size is limited to just 113 square metres – a discount of 82% of its calculated RPA and 37% of its canopy area.
Notwithstanding categorisation of the tree as A,1,2, the BNG 3.0 Condition Assessment Criteria categorises the condition of this tree as Poor because it meets only two of the six criteria, as shown below:
Using BNG 3.0, the calculation of the baseline habitat (called Habitat Units) of this tree is as follows:
Had the BS 5837:2012 condition of the tree been allowed for and its condition set to ‘Good’, then the habitat units of this tree would be three times the habitat unit value of 0.0452, i.e., 0.1356 as shown below.
Not only has the true size of the urban tree habitat been significantly undervalued (because its actual RPA has not been used), but its assessed condition using the BNG 3.0 criteria is also clearly inappropriate given that this tree has been assessed at the highest category under BS 5837:2012:
Category A – Trees of high quality with an estimated remaining life expectancy of at least 40 years …that are particularly good examples of their species, especially if rare or unusual; or those that are essential components of groups or formal or semi-formal arboricultural features (e.g., the dominant and/or principal trees within an avenue).
The proposed solution
BNG 3.0 is seriously flawed when it comes to evaluating Urban Tree habitats. We have already commented on this when it comes to calculating habitat size.
In our view, the solution to the issue of assessing the correct condition of urban tree habitats is already available in BS 5837:2012. The standard may require some amendment to align it with BNG 3.0, but it is a well-established and practical approach used by the arboricultural community. This British Standard gives recommendations and guidance on the relationship between trees and design, demolition and construction processes and is used whether or not planning permission is required.
At last, some good news: city trees have been given the same habitat and biodiversity value as their country cousins.
Or have they?
STOP PRESS
Since writing this blog, we have now responded to Defra’s Small Sites Metric (SSM) Consultation. It develops further our critique of the way that urban tree habitats are being undervalued. Perhaps urban trees are now the poor country cousin?
The important contribution that urban trees (native and non-native) make to our cities has finally been recognised by Natural England, with their publication of Biodiversity Metric 3.0 (BNG 3.0) on 7 July. It states that:
Trees in urban areas can, under the right conditions, provide a large range of habitat opportunities, supporting lichens, bryophytes, invertebrates and birds. Tree planting in urban areas has for over two hundred years also introduced non-native species into towns and cities. In the context of biodiversity, native species are the preferred option. However, non-native tree species can contribute positively to biodiversity richness particularly in relation to providing a seasonal food source for nectar feeders and other invertebrates as well as supporting vertebrates that feed on species that are hosted by non-native trees. Examples are early and late flowering species of Prunus and aphids on varieties of Acer providing food for species higher up the food chain.
Trees in urban areas provide opportunistic sites for biodiversity to colonise and re-colonise, increasing connectivity and contributing to biodiversity critical mass between already established patches or sites. This is especially true where transport corridors are populated with mixed native species.
What’s an urban tree?
The new BNG 3.0 habitat category, urban tree, includes individual trees, lines of street trees and blocks of trees growing within the urban setting.
BM3.0 Guide – TABLE 7-1: Urban tree definitions
The previous urban tree habitat categories, woodland, orchard and street tree, which appeared in the beta test version of Biodiversity Metric 2.0 (BNG 2.0) have been discarded.
The urban tree habitat calculation has been set to ‘medium’ distinctiveness and ‘low’ difficulty for both habitat creation and enhancement. Urban trees are categorised into small, medium or large. Their condition may also be assessed as poor, moderate or good.
The problem with BNG 3.0
The three size bands set out in the table below are useful when creating new habitats or enhancing existing ones (for example, nursery-raised standards ready for planting have a stem diameter of around 30 cm and so are Medium). However, these bands are not useful for assessing the baseline habitat of existing urban trees.
This is the size table used in BNG 3.0:
BM3.0 Guide – TABLE 7-2: Urban tree size by girth and their area equivalent
NB: the second column of this table is wrongly labelled. It should read Girth (circumference) at Breast Height, not Diameter.
The RPA formula used is simple: RPA radius = 12 x DBH (Stem Diameter is also known as DBH – Diameter at Breast Height). This value is then used to calculate the RPA using the formula DBH = PI * RPAr^2.
Every application to develop land where trees will be affected should produce a BS:5837-compliant survey, called an Arboricultural Impact Assessment (AIA). This will report the stem diameters of all the trees growing on and around the site. The AIA also reports several other tree features including species, height, cardinal point canopy radii, condition, life stage and the BS:5837 category – a measure of the quality of the tree.
However, the BNG 3.0 table above provides no logical way of establishing whether a given surveyed tree with a stem diameter of, say, 15 cm or 40 cm – halfway between categories – is Small, Medium, or Large.
It would be better if the table gave ranges – say Small up to 10 cm, Medium 10-50 cm and Large 50 cm or more – but this has not been done. Also, doing this would distort the habitat calculation with all Small trees set to their upper range and all Large trees set to their lower range.
Our solution
Why use the table at all? It would be far simpler to calculate a tree’s baseline habitat area just by using the calculated RPA provided in the AIA. It would be better still to use its actual measured canopy area, which will have been reported in the AIA and thus be readily available.
In our view, RPA does not reflect the habitat value of a tree. All it does is use a formulaic approach to solving the problem of finding an acceptable way to protect trees. It bears little relationship to the habitat or biodiversity value of a tree. It would be far better to calculate a tree’s canopy cover (TCC), the standard method of working out the value of a tree. Every AIA reports the canopy radii of the four cardinal compass points of each tree surveyed. These can be averaged and used to calculate TCC.
We made these observations when Natural England was consulting on its beta test version, but these seem to have been overlooked. We hope they now take note.
Some further thoughts
The introduction of the three new urban tree poor/moderate/good condition criteria, set out in detail in the BNG 3.0 Technical Supplement, will require all AIA surveys to include this data. Perhaps BS:5837 should be updated to require this to be recorded in the AIA.
Where tree surveys identify mixed urban tree conditions, the person undertaking the BNG 3.0 calculation will need to record more than one urban tree baseline habitat to capture this information.
BNG 2.0, which was only published as a beta test to allow for wider public consultation, is still being used by Bristol’s Local Planning Authority (LPA) for pending applications but needs to be abandoned. Pending applications which require a biodiversity net gain report should be required to recast their calculations using BNG 3.0 rather than still relying on BM2.0. This is particularly true for the Council’s own, direct applications such as the one pending for the Baltic Wharf Caravan Park.
Our initial analysis shows a significant net gain deficit when BNG 2.0 is used instead of BNG 3.0. This is especially true for urban street trees, which are significantly undervalued under BM2.0. Furthermore, the LPA is currently allowing applications which propose a zero net gain outcome, even though the Environment Bill (currently being considered in Parliament) will require a net gain of 10% above the baseline valuation.
Given that the Council has declared climate and ecological emergencies and aims to achieve carbon neutrality by 2030, it is surprising that developers continue to be allowed to present biodiversity net gain proposals that either undervalue biodiversity or offer no net gain whatsoever.
Conclusion
We welcome the publication of BNG 3.0, but its flaws need to be corrected.
Publishing Biodiversity Metric 3.0 was a landmark moment for biodiversity net gain, it will become the metric used to calculate and evidence whether a project has achieved the biodiversity net gain requirements set out in the Environment Bill. Biodiversity Net Gain (BNG) is:
‘an approach to development, and/or land management, that leaves nature in a measurably better state than beforehand‘ …
Biodiversity Metric 3.0 ensures that:
all habitats, from street trees to woodlands, green roofs to grasslands are recorded, scored and valued for their importance for wildlife. At the same time, it provides an evidence-based, transparent, consistent and easy to use way of ensuring that nature is considered within the design of developments and in land management practice, leaving nature in a better place than it was before, benefitting wildlife, people and places.
Bristol City Council’s declaration of climate and ecological emergencies and its commitment to achieve carbon neutrality by 2030 means that it needs now to ensure that the latest, most accurate biodiversity net gain calculations are part of all pending and future planning applications.
